Temple Illuminatus

Fix a dripping kitchen faucet with replacement parts.

How to fix a leaking faucet how to fix leaky faucet

You can fix almost any drippy single-lever kitchen faucet in about an hour. We'll show you how. The repair is a lot easier than you might think, even for a plumbing novice. So stop putting up with the annoying drip and let's fix that thing.
Time

Instant!
Complexity

Simple
Cost

Under $20

DIY faucet repair

Doing your own faucet repair may seem daunting, but once you learn the basics, modern faucets like a Moen faucet repair are fairly easy. In fact, the hardest step to fix a leaky faucet is usually finding the right replacement parts for fixes like a Moen faucet repair. In this article, we’ll tell you how to find replacement parts for something like a Moen kitchen faucet repair and show you how to stop spout drips on the three main types of single-lever faucets: rotary ball, cartridge and ceramic disc. We’re showing kitchen faucets and kitchen faucet repair for a dripping faucet, but you can fix most single-lever bath faucets using the same procedures. We’ll also show you how to stop leaks around the base of the spout and fix leaking faucets.

The tools you’ll need vary a little depending on the faucet you’re repairing. You’ll probably need an Allen wrench to remove the handle. Buy a set of small Allen wrenches, and you’ll be prepared for all kinds of leaking faucets. Most repairs also require screwdrivers and a large slip-joint pliers.

Follow These Basics For All Faucet Repairs

Before you start, examine the faucet closely to determine where the water is coming from. Leaks around the base of the spout require a different repair than a drip from the end of the spout.

Then turn off the water supply to the faucet. You’ll probably find shutoff valves under the sink. If those valves don’t work or if you don’t have any, you’ll have to close the main water valve to your entire home. After you turn off the water, open the faucet in the center position to relieve water pressure and make sure the water is shut off. Finally, cover the sink drain holes with strainer baskets or rags to avoid losing small parts down the drain.

Pay close attention to the order and orientation of parts as you remove them. A digital camera or video camera is handy for recording each step in case you forget. For easier reassembly, set the parts aside in the order they were removed. When all the parts are out, inspect the interior of the valve for bits of deteriorated gaskets or mineral deposits. Use a cloth or fine nylon abrasive pad to clean the surface. Loosen mineral deposits by soaking them in vinegar.

Slow water flow can be caused by plugged holes in the faucet body. Use a small screwdriver or penknife to clean them out. Before you replace worn parts and reassemble the faucet, hold a rag over the dripping faucet and open the water shutoff valve slightly to flush out debris that may have been loosened during the cleaning and inspection.

After the faucet is reassembled, open the faucet to the middle position and gradually open the shutoff valves to turn on the water. Leave the faucet open until water flows freely and all the air is out of the pipes. If the water flow through the faucet is slow, the aerator (Figure A) may be plugged. Unscrew the aerator and clean it out.

Take the Old Parts to the Store to Find Replacements

You’ll often find the brand name stamped on the faucet. And this information will help when it comes time to find repair parts. But in most cases, the safest bet is to take the worn parts to the store with you.

If you have a Delta or other rotary ball faucet (Figure A), you’re in luck because you’ll find repair kits in most hardware stores and home centers. Cartridges and repair kits for Moen “cartridge type” (Figure B) faucets are also readily available. But if you have another brand or a disc-type faucet, you may have to order parts, since there are too many variations for most stores to keep in stock. It helps to know the faucet’s model name or number when searching for a replacement cartridge. Otherwise, take the cartridge with you to the store so you can match it to a photo in the parts catalog.

Plumbing supply specialists are also a good source of repair parts. If you’re having trouble finding parts, call the manufacturer of your faucet for help.

Rotary ball faucets




How to Fix a Leaky Faucet

Figure A: Ball faucet parts

How rotary ball faucets are assembled.


Water flow and temperature in a rotary ball faucet are controlled by a hollow ball that rotates in a socket (Figure A). Delta and Peerless are two of the major brands. Your faucet may have a brass or plastic ball. Both work well, although the long-lasting stainless steel ball comes with most repair kits. We recommend that you buy a repair kit that includes the ball, springs, seats and O-rings for the spout, as well as a small repair tool. With this kit, you’ll be prepared for almost any repair.

If water is leaking out around the base of the handle, you may be able to fix the leak by removing the handle (Photo 1) and simply tightening the adjusting ring slightly (Figure A; a large version is available in the Addendum at the end of this article). Turn it clockwise with the spanner tool included in the repair kit. If the faucet drips from the end of the spout, replace the seats and springs (Photo 4).

Reassembly is straightforward in Delta kitchen faucet repair and other models. Drop the springs in the recesses and press the rubber seats over the top with your fingertip. Then align the groove in the ball with the pin in the socket and drop the ball in. Align the lug on the plastic cam with the notch in the valve body and set it over the ball. Thread on the cap with the adjusting ring and tighten it with the slip-joint pliers. Now you can turn on the water to check for leaks. If water leaks from around the ball stem, use the spanner tool to tighten the adjusting ring until the leak stops. Replace the handle and you’re done.

Cartridge-style faucets




How to Fix a Leaky Faucet

Figure B: Cartridge faucet parts

How cartridge-style faucets are assembled.


Many faucet brands use a cartridge of some type (Figure B, a large version is available in the Addendum at the end of this article). We show how to replace a Moen cartridge, but the process is similar for other brands. To stop drips at the spout or correct problems with hot and cold mixing, remove the cartridge and either replace the O-rings on the cartridge if they’re worn or replace the entire cartridge. Take the cartridge to the home center or hardware store to find a replacement.

Photos 1 – 6 show how to remove the cartridge. Replacement cartridges for Moen faucets include a plastic spanner cap that allows you to twist and loosen the cartridge to make it easier to pull out (Photo 5). Don’t be surprised if the cartridge seems stuck. It may take considerable force to pull it out. Really stubborn cartridges may require the use of a special cartridge-pulling tool.

Reassemble the faucet in the reverse order. Pull the stem up before inserting the cartridge. You may have to twist the cartridge slightly to line it up for the brass retainer clip. Use the plastic spanner cap or the tips of needle-nose pliers to rotate the cartridge. Slide the brass clip into the slots in the valve body to hold the cartridge in place.

Look for the small notch on top of the stem and rotate the stem until the notch faces you (Photo 4). Install the remaining parts and reattach the handle. The directions that come with the stem will help orient you here. Then test the faucet. If the hot and cold water are reversed, simply remove the handle, dome assembly and handle adapter and rotate the stem 180 degrees.

Ceramic disc faucets




How to Fix a Leaky Faucet

Figure C: Ceramic faucet parts

How ceramic disc faucets are assembled.


Ceramic disc valves are simply another type of cartridge. Discs inside the cartridge control the water flow. This type of valve is sturdy and reliable and rarely needs fixing. In fact, many manufacturers offer a lifetime guarantee on the cartridge. If yours is damaged, check with the manufacturer to see if it’s covered by a warranty.

Leaks can result from faulty rubber seals or a cracked disc inside the cartridge. Since it’s difficult to spot a cracked disc, and disc cartridge replacements are very expensive, it’s best to start by replacing the seals and reassembling the faucet. Then if the faucet still leaks, remove the disc cartridge and take it to the store to order a replacement.

Early versions of ceramic disc faucets may be more fragile and can crack if subjected to a blast of pressurized air. That’s why it’s important to leave the faucet open as you turn the water back on. This allows air trapped in the lines to escape. When the water runs smoothly, it’s safe to turn the faucet off. Manufacturers have improved the strength of ceramic discs on newer faucets to withstand air blasts, as well as abrasive debris that may get dislodged from the inside of pipes.

To see how a ceramic disc is assembled, see Figure C (a large version is available in the Addendum at the end of this article).

S




How to Fix a Leaky Faucet

Step 1: Remove the spout to access the o-ring seals

Photo 1: Remove the handle and cartridge. Twist and pull up on the spout to remove it and expose the O-ring seals.


Leaks around the base of the spout are caused by worn O-rings located under the spout. All that’s usually required to access these O-rings for replacement is to wiggle and pull up on the spout to remove it (Photo 1).

Depending on the faucet, you’ll also have to remove the handle and other parts to access the spout. Be persistent. The spout may be a little stubborn. Spout O-ring kits are available for many faucets, or you can take the old O-rings to the hardware store or plumbing supply store and match them up with new ones. Remember to pick up a small toothpaste-type tube of plumber’s grease while you’re there.

In Photo 1, you can see the diverter valve, which controls water to the sprayer. Their appearance varies considerably among brands, but you’ll usually find them under the spout. If your sprayer isn’t working properly, first clean it in vinegar or simply replace it. If this doesn’t work, the diverter valve may be clogged. If it doesn’t simply pull out, contact the manufacturer or ask a knowledgeable salesperson for help with cleaning it.

Additional Information

Required Tools for this Project

Have the necessary tools for this how to fix a dripping faucet DIY project lined up before you start—you’ll save time and frustration.

  • 4-in-1 screwdriver
  • Allen wrench
  • Pliers
  • Slip joint pliers

Required Materials for this Project

Avoid last-minute shopping trips by having all your materials ready ahead of time. Here’s a list.

  • Faucet repair kit
  • O-ring seals

https://www.familyhandyman.com/plumbing/faucet-repair/how-to-repair...

Views: 19

Have questions?

Need help? Visit our Support Group for help from our friendly Admins and members!

Have you?

Become a Member
Invited Your Friends
Made new Friends
Read/ Written a Blog
Joined/ Created a Group
Read/ Posted a Discussion
Checked out the Chat
Looked at/Posted Videos
Made a donation this month
Followed us on Twitter
Followed us on Facebook

Donations

Please consider a donation to help with our continued growth and site costs

Connect

Visit The Temple
on Facebook:

....

Blog Posts

HAPPY MABON TO ALL

Posted by Linda M. on September 22, 2018 at 11:00am 0 Comments

The Fall of Babylon (The New Atlantis)

Posted by Quingu on September 20, 2018 at 5:00pm 0 Comments

Lycanthropy

Posted by Quingu on September 20, 2018 at 4:00pm 0 Comments

The Chaos Dragon

Posted by Quingu on September 19, 2018 at 1:51pm 0 Comments

The Monarch Butterfly (Mind Control)

Posted by Quingu on September 14, 2018 at 6:00am 0 Comments

Fool's Gold (The Soul)

Posted by Quingu on September 14, 2018 at 6:00am 0 Comments

The Draconian Path

Posted by Quingu on September 14, 2018 at 5:56am 0 Comments

The Great Sacrifice

Posted by Quingu on September 14, 2018 at 5:54am 0 Comments

The Imdugud (Half Eagle/Half Lion)

Posted by Quingu on September 14, 2018 at 5:52am 0 Comments

The Paa Taal & The Draconians

Posted by Quingu on September 14, 2018 at 5:49am 0 Comments

Orion Hive Mind Intelligence

Posted by Quingu on September 14, 2018 at 5:30am 0 Comments

The Angel Samael

Posted by Quingu on September 14, 2018 at 5:30am 0 Comments

OUR LADY! A ROSE!

Posted by Rosey on September 13, 2018 at 9:09pm 0 Comments

Mabon Ritual To Honor the Dark Mother

Posted by Helela on September 4, 2018 at 10:00pm 4 Comments

Womb of life

Posted by Lilly on September 3, 2018 at 2:20pm 2 Comments

time and purpose

Posted by Iblis Lucifer Sauron on September 2, 2018 at 10:00pm 1 Comment

~~this months awareness~~

© 2018   Created by Bryan   Powered by

Badges  |  Report an Issue  |  Terms of Service